Description:

PLEASE NOTE -Introducutory pricing on all units ordered prior to 7/1/2026

The 7in and 12in High resolution full colour with outstanding readability in direct sunlight with Numerous selectable layouts are supplied.

Working with a Syvecs or Motec standalone ECU brings information to a new level. Allowing any piece of information the ECU uses and sees to be transmitted over canbus to the dash to be displayed. The dashes both have 2 x can inputs which are both used in our kits, one for ECU canbus input, the other for OEM canbus input.

Both dashes have the same features regarding inputs and outputs, but only the C127 has dedicated 16 LED lights which are fully configurable for warnings, shift lights, anything you may think of. The C1212 and be programmed with icons to notify you or full screen flashes for shift lights.

Limp modes and Alarms are configured and alerted through the ECU when a problem comes about describing the Limp mode, to allow you to decided what needs to be done next.

We have kept the OEM dash look on our main screen page replicating the look where the C127 has shortened version and the C1212 has the full display with both gauges.

We have composed 4 pages in our packages, Main OEM page, Second display page, Drag type page and final page with all the information available to be shown for easy diagnosis

On the OEM canbus side we can display all your information from Lights( High, Low beam, Parkers, Auto Light selection, Indicators, Hazard light) Cruse Control, Water Spray, OEM Traction control Active Flash,Doors, Seat belt, Handbrake, AFS OFF, Battery, Oil light, Engine Light, ABS Lights, Including error lights for ABS, Charging System, SST Transmission, SST Transmission Overheat, Major Error codes, error codes are treated as per any car where you will scan the car to check the actual issue. Minor codes will still trigger the Engine Light. Fuel Level works, this is sent as a output into your ECU and a voltage input and then sent via the ECU canbus to the dash.

We have set up the dash to keep you only needing the Dash Creator upgrade to be active without needing the extra input/output upgrade. The available inputs have been used with our kit. Our kit is setup to use 2 x momentary switches which will have the wires populated in the main AMP motec plug to allow your choice and location of buttons, one button for page changing and one for alarm reset and trip milage reset.

As these are a ADR approved dash in Australia, we can put your actual Odometer reading from you OEM dash, this can only be set by Motec and cannot be modified by anyone else other than them.

Our Plug in harness will connect to the OEM dash plug for information, and also have a output for Fuel level to go to your ECU input, OEM canbus wiring to be joined to the OEM Harness under the dash, the other plug will have the power supply wires and ECU canbus all to be connected.

We will be able to do extra custom work for specific items or screens but that would be an extra rate depending on the service, our package already has allowance for Nitrous and Water Meth information included.

*There will be slight variations between ECU eg Syvecs and Motec information and also SST DCT gearbox and 5 speed.

There will be access in Display Manager program to change shift lights and LED allocations, Alarms and preserved channels.

The printed dashes fit like OEM and reuse the OEM white clips from your OEM dash.

C127 dash requires no modification and mounts straight in. the C1212 does require extensive cutting but its worth the effort to fit in, as our version sits in deep and you get to see the whole screen. To keep the cleaning mess simple we would suggest removing the dash skin and cutting out of the car, which will take approx. 1hr to remove but will make the job a lot easier, then reinstall with only minor touches up to do in the car, we supply installation instruction info for this purpose. For the ones not wanting to cut thier existing surrond just remember you can always buy a second hand dash skin from us to fit and always keep you original OEM one untouched.

Motec is the only dash capable of being able to handle the levels of canbus integration and customization and this reflects in the price, but remember you get what you pay for with the quality and functions.